欢迎访问济南鑫浩语重工有限公司官网

单列圆锥滚子轴承设计用于适应组合载荷，即同时作用的径向和轴向载荷。滚道的延长线交汇于轴承轴线上的同一点，以实现真实的滚动，因此在运行期间具有低的摩擦力矩。圆锥滚子轴承的轴向载荷能力随着接触角 α 的增大而增加。接触角的大小（通常为 10° 至 30°）与计算系数 e 有关（根据产品表）：e 值越大，接触角越大。

Single-row tapered roller bearings are designed to accommodate combined loads, i.e. radial and axial loads acting simultaneously. The extensions of the raceways meet at the same point on the bearing axis to achieve true rolling and therefore low friction moments during operation. The axial load capacity of tapered roller bearings increases with increasing contact angle α. The size of the contact angle (usually 10° to 30°) is related to the calculation factor e (according to the product table): the larger the value of e, the larger the contact angle.

特点和优点

*低摩擦

优化的滚子端设计和法兰上的表面光洁度促进了润滑膜的形成，从而降低了摩擦。这还可以减少摩擦热和法兰磨损。此外，轴承可以更好地保持预紧力并在较低的噪音水平下运行。

*使用寿命长

与传统的直线滚道轮廓相比，基本设计轴承的冠状滚道轮廓和对数滚道轮廓优化了沿接触表面的负载分布，降低了滚子端的应力峰值，并降低了对错位和轴偏转的敏感度。

*增强的操作可靠性

滚子和滚道接触表面上的优化表面光洁度支持流体动力润滑膜的形成。

*滚子轮廓和尺寸的一致性

圆锥滚子轴承中的滚子制造成非常紧密的尺寸和几何公差，以至于它们几乎相同。这提供了最佳的负载分布，降低了噪音和振动，并使预紧力设置得更准确。

*刚性轴承应用

单列圆锥滚子轴承通常相对于第二个圆锥滚子轴承进行调整。通过施加预紧力，可以实现刚性轴承应用。

*磨合期温度峰值降低

圆锥滚子轴承通常有一个磨合期，在此期间，传统设计的圆锥滚子轴承会经历大量摩擦，导致磨损。这种影响表现为温度峰值。只要轴承安装和润滑正确，摩擦、摩擦热和磨损就会显著减少。

*可分离和可互换

内圈与滚子和保持架组件（锥体）可以与外圈（杯体）分开安装。此外，可分离组件是可互换的。这方便了安装、拆卸和维护检查程序。

Features and benefits

*Low friction

The optimized roller end design and surface finish on the flangepromote lubricant film formation, resulting in lower friction. This also reduces frictional heat and flange wear. In addition, the bearings can better maintain preload and run at reduced noise levels.

*Long service life

The crowned raceway profiles of basic design bearings and the logarithmic raceway profiles optimize the load distribution along the contact surfaces, reduce stress peaks at the roller ends, and reduce the sensitivity to misalignment and shaft deflection compared with conventional straight raceway profiles.

*Enhanced operational reliability

Optimized surface finish on the contact surfaces of the rollers and raceways supports the formation of a hydrodynamic lubricant film.

*Consistency of roller profiles and sizes

The rollers incorporated tapered roller bearings are manufactured to such close dimensional and geometrical tolerances that they are practically identical. This provides optimal load distribution, reduces noise and vibration, and enables preload to be set more accurately.

*Rigid bearing application

A single row tapered roller bearing is typically adjusted against a second tapered roller bearing. By applying a preload, a rigid bearing application can be achieved.

*Running-in period with reduced temperature peaks

Tapered roller bearings typically have a running-in period, during which a conventional design tapered roller bearing experiences a significant amount of friction, resulting in wear. This effect is noticed as a temperature spike. When bearings are mounted and lubricated correctly, friction, frictional heat and wear are significantly reduced.

*Separable and interchangeable

The inner ring with roller and cage assembly (cone) can be mounted separately from the outer ring (cup). Furthermore, the separable components are interchangeable. This facilitates mounting, dismounting and also maintenance inspection routines.

轴承类型		国内新型号	国内旧型号	规格(dxDxT)	重量(kg)
圆锥滚子轴承	Tapered roller bearings	32907	2007907E	35×55×14	-
圆锥滚子轴承	Tapered roller bearings	32908	2007908	40×62×15	-
圆锥滚子轴承	Tapered roller bearings	32908	2007908E	40×62×15	0.139
圆锥滚子轴承	Tapered roller bearings	32909	2007909E	45×68×15	-
圆锥滚子轴承	Tapered roller bearings	32910	2007910E	50×72×15	-
圆锥滚子轴承	Tapered roller bearings	32911	2007911E	55×80×17	-
圆锥滚子轴承	Tapered roller bearings	92312	2007912	60×85×17	0.24
圆锥滚子轴承	Tapered roller bearings	32912	2007912E	60×85×17	0.24
圆锥滚子轴承	Tapered roller bearings	32913	2007913E	65×90×17	0.317
圆锥滚子轴承	Tapered roller bearings	32914	2007914E	70×100×20	0.472
圆锥滚子轴承	Tapered roller bearings	32914	2007914	70×100×20	-
圆锥滚子轴承	Tapered roller bearings	32915	2007915	75×105×20	0.479
圆锥滚子轴承	Tapered roller bearings	32915	2007915E	75×105×20	-
圆锥滚子轴承	Tapered roller bearings	32916	2007916	80×110×20	0.523
圆锥滚子轴承	Tapered roller bearings	32916	2007916E	80×110×20	-
圆锥滚子轴承	Tapered roller bearings	32917	2007917E	85×120×23	-
圆锥滚子轴承	Tapered roller bearings	32918	2007918	90×125×23	0.809
圆锥滚子轴承	Tapered roller bearings	32918	2007918E	90×125×23	-
圆锥滚子轴承	Tapered roller bearings	32919	2007919	90×130×23	0.845
圆锥滚子轴承	Tapered roller bearings	32919	2007919E	90×130×23	-
圆锥滚子轴承	Tapered roller bearings	32920	2007920	100×140×25	1.13
圆锥滚子轴承	Tapered roller bearings	32920	2007920E	100×140×25	-
圆锥滚子轴承	Tapered roller bearings	32921	2007921	105×145×25	1.177
圆锥滚子轴承	Tapered roller bearings	32921	2007921E	105×145×25	-
圆锥滚子轴承	Tapered roller bearings	32922	2007922	110×150×25	1.222
圆锥滚子轴承	Tapered roller bearings	32922	2007922E	110×150×25	-
圆锥滚子轴承	Tapered roller bearings	32924	2007924E	120×165×29	1.69
圆锥滚子轴承	Tapered roller bearings	32926	2007926E	130×180×32	2.31
圆锥滚子轴承	Tapered roller bearings	32928	2007928	140×190×32	-
圆锥滚子轴承	Tapered roller bearings	32930	2007930E	150×210×38	3.56
圆锥滚子轴承	Tapered roller bearings	32932	2007932E	160×220×38	3.79
圆锥滚子轴承	Tapered roller bearings	32934	2007934E	170×230×38	3.86
圆锥滚子轴承	Tapered roller bearings	32934YA	2007934	170×230×38.5	-
圆锥滚子轴承	Tapered roller bearings	32936	2007936	180×250×45	-
圆锥滚子轴承	Tapered roller bearings	32936	2007936E	180×250×45	-
圆锥滚子轴承	Tapered roller bearings	32938	2007938E	190×260×45	6.25
圆锥滚子轴承	Tapered roller bearings	32940	2007940E	200×280×51	8.86
圆锥滚子轴承	Tapered roller bearings	32944	2007944	220×300×51	10.1
圆锥滚子轴承	Tapered roller bearings	32944	2007944E	220×300×51	-
圆锥滚子轴承	Tapered roller bearings	32948	2007948E	240×320×51	10.8
圆锥滚子轴承	Tapered roller bearings	32948/YB2	2007948	240×320×51	-
圆锥滚子轴承	Tapered roller bearings	32952	2007952E	260×360×63.5	19.2
圆锥滚子轴承	Tapered roller bearings	32956	2007956E	280×380×63.5	20
圆锥滚子轴承	Tapered roller bearings	32960	2007960E	300×420×76	30.2
圆锥滚子轴承	Tapered roller bearings	32964	2007964E	320×440×76	44.7
圆锥滚子轴承	Tapered roller bearings	32968	2007968E	340×460×76	34.3
圆锥滚子轴承	Tapered roller bearings	32968	2007968	340×460×76	-
圆锥滚子轴承	Tapered roller bearings	32972	2007972E	360×480×76	38.5
圆锥滚子轴承	Tapered roller bearings	32972	2007972	360×480×76	36.4
圆锥滚子轴承	Tapered roller bearings	32004	2007104	20×42×15	0.097
圆锥滚子轴承	Tapered roller bearings	32004	2007104E	20×42×15	-
圆锥滚子轴承	Tapered roller bearings	320/22	20071/22E	22×44×15	-
圆锥滚子轴承	Tapered roller bearings	32005	2007105	25×47×15	0.11
圆锥滚子轴承	Tapered roller bearings	32005	2007105E	25×47×15	-
圆锥滚子轴承	Tapered roller bearings	32005YA	2007105EK	25×47×15	0.11
圆锥滚子轴承	Tapered roller bearings	320/28	20071/28E	28×52×16	-
圆锥滚子轴承	Tapered roller bearings	32006	2007106	30×55×17	0.16
圆锥滚子轴承	Tapered roller bearings	32006	2007106E	30×55×17	0.169
圆锥滚子轴承	Tapered roller bearings	320/32	20071/32	32×58×17	0.182
圆锥滚子轴承	Tapered roller bearings	320/32	20071/32E	32×58×17	-
圆锥滚子轴承	Tapered roller bearings	32007	2007107	35×62×18	0.224
圆锥滚子轴承	Tapered roller bearings	32007	2007107E	35×62×18	-
圆锥滚子轴承	Tapered roller bearings	32008	2007108	40×68×19	0.265
圆锥滚子轴承	Tapered roller bearings	32008	2007108E	40×68×19	-
圆锥滚子轴承	Tapered roller bearings	32009	2007109	45×75×20	0.32
圆锥滚子轴承	Tapered roller bearings	32009	2007109E	45×75×20	-
圆锥滚子轴承	Tapered roller bearings	32010	2007110	50×80×20	0.381
圆锥滚子轴承	Tapered roller bearings	32010/YB2	2007110EK	50×80×20	0.373
圆锥滚子轴承	Tapered roller bearings	32010	2007110E	50×80×20	-
圆锥滚子轴承	Tapered roller bearings	32011	2007111	55×90×23	0.551
圆锥滚子轴承	Tapered roller bearings	32011	2007111E	55×90×23	0.564
圆锥滚子轴承	Tapered roller bearings	32012	2007112	60×95×23	0.56
圆锥滚子轴承	Tapered roller bearings	32012	2007112E	60×95×23	0.59
圆锥滚子轴承	Tapered roller bearings	32012	2007112FKT	60×95×23	0.544
圆锥滚子轴承	Tapered roller bearings	32013	2007113	65×100×23	0.63
圆锥滚子轴承	Tapered roller bearings	32013	2007113E	65×100×23	-
圆锥滚子轴承	Tapered roller bearings	32014	2007114	70×110×25	0.85
圆锥滚子轴承	Tapered roller bearings	32014	2007114E	70×110×25	-
圆锥滚子轴承	Tapered roller bearings	32015	2007115	75×115×25	0.88
圆锥滚子轴承	Tapered roller bearings	32015	2007115E	75×115×25	-
圆锥滚子轴承	Tapered roller bearings	32016	2007116	80×125×29	1.19
圆锥滚子轴承	Tapered roller bearings	32016	2007116E	80×125×29	1.26
圆锥滚子轴承	Tapered roller bearings	32017	2007117	85×130×29	1.33
圆锥滚子轴承	Tapered roller bearings	32017	2007117E	85×130×29	1.33
圆锥滚子轴承	Tapered roller bearings	32018	2007118	90×140×32	1.66
圆锥滚子轴承	Tapered roller bearings	32018	2007118EX	90×140×32	1.69
圆锥滚子轴承	Tapered roller bearings	32018	2007118E	90×140×32	1.77
圆锥滚子轴承	Tapered roller bearings	32019	2007119	95×145×32	1.79
圆锥滚子轴承	Tapered roller bearings	32019	2007119E	95×145×32	1.82
圆锥滚子轴承	Tapered roller bearings	32019	2007120	100×150×32	1.87
圆锥滚子轴承	Tapered roller bearings	32020	2007120E	100×150×32	1.87
圆锥滚子轴承	Tapered roller bearings	32021	2007121	105×160×35	2.27
圆锥滚子轴承	Tapered roller bearings	32021	2007121E	105×160×35	-
圆锥滚子轴承	Tapered roller bearings	32021/YA	2007121EK	105×160×35	2.4
圆锥滚子轴承	Tapered roller bearings	32022	2007122	110×170×38	2.9
圆锥滚子轴承	Tapered roller bearings	32022	2007122E	-	-
圆锥滚子轴承	Tapered roller bearings	32022Z1	2007122EZ1	110×170×38	-
圆锥滚子轴承	Tapered roller bearings	32022/DF	2047122	110×170×76	6.17
圆锥滚子轴承	Tapered roller bearings	32024	2007124	120×180×38	3.1
圆锥滚子轴承	Tapered roller bearings	32024	2007124E	120×180×38	-
圆锥滚子轴承	Tapered roller bearings	32024/YA	2007124K	120×180×38	3.07
圆锥滚子轴承	Tapered roller bearings	32026	2007126	130×200×45	4.66
圆锥滚子轴承	Tapered roller bearings	32026	2007126E	130×200×45	4.626
圆锥滚子轴承	Tapered roller bearings	32026/Z1	2007126EZ1	130×200×45	4.94
圆锥滚子轴承	Tapered roller bearings	32028	2007128	140×210×45	5.21
圆锥滚子轴承	Tapered roller bearings	32028	2007128E	140×210×45	-
圆锥滚子轴承	Tapered roller bearings	32028/DF	2047128	140×210×90	12
圆锥滚子轴承	Tapered roller bearings	32028L1	2007128EL	140×210×45	5.1
圆锥滚子轴承	Tapered roller bearings	32030	2007130E	150×225×48	6.2
圆锥滚子轴承	Tapered roller bearings	32032	2007132E	160×240×51	7.7
圆锥滚子轴承	Tapered roller bearings	32034	2007134	170×260×57	10.1
圆锥滚子轴承	Tapered roller bearings	32034	2007134E	170×260×57	10.1
圆锥滚子轴承	Tapered roller bearings	32036	2007136	180×280×64	13
圆锥滚子轴承	Tapered roller bearings	32036	2007136E	180×280×64	13
圆锥滚子轴承	Tapered roller bearings	32038	2007138	190×290×64	15.3
圆锥滚子轴承	Tapered roller bearings	32038	2007138E	190×290×64	15.3
圆锥滚子轴承	Tapered roller bearings	32040	2007140	200×310×70	17
圆锥滚子轴承	Tapered roller bearings	32040	2007140E	200×310×70	17
圆锥滚子轴承	Tapered roller bearings	32040/YA	2007140	200×310×70	-
圆锥滚子轴承	Tapered roller bearings	32044	2007144	220×340×76	23.3
圆锥滚子轴承	Tapered roller bearings	32044	2007144E	220×340×76	23.3
圆锥滚子轴承	Tapered roller bearings	32044/YA	2007144	220×340×76	23.4
圆锥滚子轴承	Tapered roller bearings	32048	2007148	240×360×76	24
圆锥滚子轴承	Tapered roller bearings	32048	2007148E	240×360×76	24
圆锥滚子轴承	Tapered roller bearings	32048/YA	2007148	240×360×76	25.5
圆锥滚子轴承	Tapered roller bearings	32048/HC	2007148S	240×360×76	24.9
圆锥滚子轴承	Tapered roller bearings	32052	2007152	260×400×87	37.8
圆锥滚子轴承	Tapered roller bearings	32052	2007152E	260×400×87	-
圆锥滚子轴承	Tapered roller bearings	32056	2007156	280×420×87	39.6
圆锥滚子轴承	Tapered roller bearings	32056	2007156E	280×420×87	-
圆锥滚子轴承	Tapered roller bearings	32060	2007160E	300×460×100	55.9
圆锥滚子轴承	Tapered roller bearings	32060/HC	2007160S	300×460×100	-
圆锥滚子轴承	Tapered roller bearings	32064	2007164	320×480×100	59.1
圆锥滚子轴承	Tapered roller bearings	32064/YA	2007164	320×480×100	58.6
圆锥滚子轴承	Tapered roller bearings	32064	2007164E	320×480×100	59.1
圆锥滚子轴承	Tapered roller bearings	33005	3007105	25×47×17	0.131
圆锥滚子轴承	Tapered roller bearings	33006	3007106	30×55×20	0.208
圆锥滚子轴承	Tapered roller bearings	33007	3007107	35×62×21	0.267
圆锥滚子轴承	Tapered roller bearings	33008	3007108	40×68×22	0.322
圆锥滚子轴承	Tapered roller bearings	33009	3007109	45×75×24	0.414
圆锥滚子轴承	Tapered roller bearings	33010	3007110	50×80×24	0.452
圆锥滚子轴承	Tapered roller bearings	33011	3007111	55×90×27	0.672
圆锥滚子轴承	Tapered roller bearings	33012	3007112	60×95×27	0.713
圆锥滚子轴承	Tapered roller bearings	33013	3007113	65×100×27	0.758
圆锥滚子轴承	Tapered roller bearings	33014	3007114	70×110×31	1.11
圆锥滚子轴承	Tapered roller bearings	33015	3007115	75×115×31	1.18
圆锥滚子轴承	Tapered roller bearings	33016	3007116	80×125×36	1.65
圆锥滚子轴承	Tapered roller bearings	33017	3007117	85×130×36	1.75
圆锥滚子轴承	Tapered roller bearings	33018	3007118	90×140×39	2.157
圆锥滚子轴承	Tapered roller bearings	33018/DF	3007118	90×140×78	4.37
圆锥滚子轴承	Tapered roller bearings	33019	3007119	95×145×39	2.32
圆锥滚子轴承	Tapered roller bearings	33019	3007119E	95×145×39	2.3
圆锥滚子轴承	Tapered roller bearings	33020	3007120	100×150×39	2.4
圆锥滚子轴承	Tapered roller bearings	33020	3007120E	100×150×39	-
圆锥滚子轴承	Tapered roller bearings	33021	3007121	105×160×43	3.05
圆锥滚子轴承	Tapered roller bearings	33021	3007121E	105×160×43	-
圆锥滚子轴承	Tapered roller bearings	33022	3007122	110×170×47	3.75
圆锥滚子轴承	Tapered roller bearings	33024	3007124	120×180×48	-
圆锥滚子轴承	Tapered roller bearings	33108	3007708	40×75×26	0.51
圆锥滚子轴承	Tapered roller bearings	33109	3007709	45×80×26	0.552
圆锥滚子轴承	Tapered roller bearings	33110	3007710	50×85×26	0.597
圆锥滚子轴承	Tapered roller bearings	33111	3007711	55×95×30	0.877
圆锥滚子轴承	Tapered roller bearings	33111	3007711E	55×95×30	-
圆锥滚子轴承	Tapered roller bearings	33112	3007712	60×100×30	0.91
圆锥滚子轴承	Tapered roller bearings	33113	3007713	65×110×34	1.32
圆锥滚子轴承	Tapered roller bearings	33114	3007714	70×120×37	1.71
圆锥滚子轴承	Tapered roller bearings	33115	3007715	75×125×37	1.796
圆锥滚子轴承	Tapered roller bearings	33116	3007716	80×130×37	1.88
圆锥滚子轴承	Tapered roller bearings	33117	3007717	85×140×41	2.51
圆锥滚子轴承	Tapered roller bearings	33118	3007718	90×150×45	3.216
圆锥滚子轴承	Tapered roller bearings	33118	3007718E	90×150×45	-
圆锥滚子轴承	Tapered roller bearings	33118/YB2	-	90×150×45	-
圆锥滚子轴承	Tapered roller bearings	33118/DF	3047718	90×150×90	6.43
圆锥滚子轴承	Tapered roller bearings	33119	3007719	95×160×49	-
圆锥滚子轴承	Tapered roller bearings	33120	3007720	100×165×52	-
圆锥滚子轴承	Tapered roller bearings	33121	3007721	105×175×56	-
圆锥滚子轴承	Tapered roller bearings	33122	3007722	110×180×56	-
圆锥滚子轴承	Tapered roller bearings	33122	3007722	110×180×56	5.53
圆锥滚子轴承	Tapered roller bearings	33124	3007724	120×200×62	-
圆锥滚子轴承	Tapered roller bearings	30202	7202	15×35×12	0.05
圆锥滚子轴承	Tapered roller bearings	30202	7202E	15×35×12	-
圆锥滚子轴承	Tapered roller bearings	30203	7203E	17×40×13.25	0.0781
圆锥滚子轴承	Tapered roller bearings	30204	7204E	20×47×15.25	0.12
圆锥滚子轴承	Tapered roller bearings	30205	7205E	25×52×16.25	0.144
圆锥滚子轴承	Tapered roller bearings	30206	7206E	30×62×17.25	0.232
圆锥滚子轴承	Tapered roller bearings	30206	7206	30×62×17.25	0.232
圆锥滚子轴承	Tapered roller bearings	302/32	72/32E	32×65×18.25	0.267
圆锥滚子轴承	Tapered roller bearings	302/32	72/32	32×65×18.25	0.28
圆锥滚子轴承	Tapered roller bearings	30207	7207E	35×72×18.25	0.318
圆锥滚子轴承	Tapered roller bearings	30207/YB2	-	35×72×18.25	0.33
圆锥滚子轴承	Tapered roller bearings	30208	7208E	40×80×19.75	0.4
圆锥滚子轴承	Tapered roller bearings	30209	7209E	45×85×20.75	0.442
圆锥滚子轴承	Tapered roller bearings	30209/HP	7209PN	45×85×20.75	0.475
圆锥滚子轴承	Tapered roller bearings	30209	7209ELK	45×85×20.75	-
圆锥滚子轴承	Tapered roller bearings	30210	7210	50×90×21.75	0.55
圆锥滚子轴承	Tapered roller bearings	30210	7210E	50×90×21.75	0.52
圆锥滚子轴承	Tapered roller bearings	32010	7210EUK	50×90×22	0.49
圆锥滚子轴承	Tapered roller bearings	30211	7211E	55×100×22.75	0.705
圆锥滚子轴承	Tapered roller bearings	30212	7212E	60×110×23.75	0.886
圆锥滚子轴承	Tapered roller bearings	32012	7212EK	60×110×23.75	0.901
圆锥滚子轴承	Tapered roller bearings	30213	7213E	65×120×24.75	1.16
圆锥滚子轴承	Tapered roller bearings	30214	7214E	70×125×26.25	1.25
圆锥滚子轴承	Tapered roller bearings	30214/T	7214M	70×125×26.25	1.29
圆锥滚子轴承	Tapered roller bearings	30215	7215E	75×130×27.25	1.34
圆锥滚子轴承	Tapered roller bearings	30215/S0	7215ET	75×130×27.25	-
圆锥滚子轴承	Tapered roller bearings	30215	7215EK	75×130×27.25	1.35
圆锥滚子轴承	Tapered roller bearings	30216	7216E	80×140×28.25	1.65
圆锥滚子轴承	Tapered roller bearings	30217	7217E	85×150×30.5	2.03
圆锥滚子轴承	Tapered roller bearings	30218	7218E	90×160×32.5	2.56
圆锥滚子轴承	Tapered roller bearings	30218	7218EK	90×160×32.5	-
圆锥滚子轴承	Tapered roller bearings	30219	7219E	95×170×34.5	3.17
圆锥滚子轴承	Tapered roller bearings	30220	7220E	100×180×37	3.73
圆锥滚子轴承	Tapered roller bearings	30221	7221E	105×190×39	4.401
圆锥滚子轴承	Tapered roller bearings	30222	7222E	110×200×41	5.27
圆锥滚子轴承	Tapered roller bearings	30224	7224E	120×215×43.5	6.21
圆锥滚子轴承	Tapered roller bearings	30226	7226E	130×230×43.75	7.02
圆锥滚子轴承	Tapered roller bearings	30228	7228E	140×250×45.75	8.8
圆锥滚子轴承	Tapered roller bearings	30230	7230E	150×270×49	10.2
圆锥滚子轴承	Tapered roller bearings	30232	7232E	160×290×52	13.5
圆锥滚子轴承	Tapered roller bearings	30234	7234E	170×310×57	-
圆锥滚子轴承	Tapered roller bearings	30236	7236E	180×320×57	18.5
圆锥滚子轴承	Tapered roller bearings	30238	7238E	190×340×60	20.6
圆锥滚子轴承	Tapered roller bearings	30240	7240E	200×400×72	27.8
圆锥滚子轴承	Tapered roller bearings	30244	7244E	220×400×72	35.5
圆锥滚子轴承	Tapered roller bearings	30244/S0	7244ET	220×400×72	35.5
圆锥滚子轴承	Tapered roller bearings	30244	7244T	220×400×72	-
圆锥滚子轴承	Tapered roller bearings	30248	7248E	240×440×79	46.4
圆锥滚子轴承	Tapered roller bearings	30252	7252E	260×480×89	62.4
圆锥滚子轴承	Tapered roller bearings	30256	7256E	280×500×89	66
圆锥滚子轴承	Tapered roller bearings	32203	7503E	17×40×17.25	-
圆锥滚子轴承	Tapered roller bearings	32204	7504E	20×47×19.25	0.158
圆锥滚子轴承	Tapered roller bearings	32205	7505	25×52×19.25	0.174
圆锥滚子轴承	Tapered roller bearings	32205	7505E	25×52×19.25	0.199
圆锥滚子轴承	Tapered roller bearings	32206	7506E	30×62×21.25	0.282
圆锥滚子轴承	Tapered roller bearings	32207	7507E	35×72×24.25	0.449
圆锥滚子轴承	Tapered roller bearings	32207	7507EK	35×72×24.25	0.423
圆锥滚子轴承	Tapered roller bearings	32208	7508E	40×80×24.75	0.533
圆锥滚子轴承	Tapered roller bearings	32209	7509E	45×85×24.75	0.583
圆锥滚子轴承	Tapered roller bearings	32209	7509EK	45×85×24.75	0.587
圆锥滚子轴承	Tapered roller bearings	32210	7510E	50×90×24.75	0.614
圆锥滚子轴承	Tapered roller bearings	32211	7511	55×100×26.75	0.93
圆锥滚子轴承	Tapered roller bearings	32211	7511E	55×100×26.75	0.849
圆锥滚子轴承	Tapered roller bearings	32211	7511EK	55×100×26.75	0.875
圆锥滚子轴承	Tapered roller bearings	32212	7512E	60×110×29.75	1.1
圆锥滚子轴承	Tapered roller bearings	32213	7513E	65×120×32.75	1.57
圆锥滚子轴承	Tapered roller bearings	32213/Z1	7513Z1	-	-
圆锥滚子轴承	Tapered roller bearings	32214	7514E	70×125×33.25	1.56
圆锥滚子轴承	Tapered roller bearings	32215	7515E	75×130×33.25	1.56
圆锥滚子轴承	Tapered roller bearings	32216	7516E	80×140×32.25	2
圆锥滚子轴承	Tapered roller bearings	32217	7517E	85×150×38.5	2.69
圆锥滚子轴承	Tapered roller bearings	32218	7518E	90×160×42.5	3.3
圆锥滚子轴承	Tapered roller bearings	32218/Z	7518EZ	90×160×42.5	3.5
圆锥滚子轴承	Tapered roller bearings	32218/Z1	7518EZ1	90×160×42.5	3.3
圆锥滚子轴承	Tapered roller bearings	32219	7519E	95×170×45.5	4.18
圆锥滚子轴承	Tapered roller bearings	32220	7520E	100×180×40	5.14
圆锥滚子轴承	Tapered roller bearings	32221	7521	105×90×53	6.29
圆锥滚子轴承	Tapered roller bearings	32221	7521E	105×90×53	6.34
圆锥滚子轴承	Tapered roller bearings	32222	7522E	110×200×56	-
圆锥滚子轴承	Tapered roller bearings	32224	7524E	120×215×61.5	9.6
圆锥滚子轴承	Tapered roller bearings	32226	7526E	130×230×67.75	11.9
圆锥滚子轴承	Tapered roller bearings	32226	7526EY	130×230×67.75	11.9
圆锥滚子轴承	Tapered roller bearings	32228	7528E	140×250×71.75	14.7
圆锥滚子轴承	Tapered roller bearings	32230	7530E	150×270×77	18.2
圆锥滚子轴承	Tapered roller bearings	32232	7532E	160×290×84	21.1
圆锥滚子轴承	Tapered roller bearings	32234	7534E	170×310×91	-
圆锥滚子轴承	Tapered roller bearings	32236	7536	180×320×91	27.9
圆锥滚子轴承	Tapered roller bearings	32236	7536E	180×320×91	29.8
圆锥滚子轴承	Tapered roller bearings	32238	7538	190×340×97	35.7
圆锥滚子轴承	Tapered roller bearings	32238	7538E	190×340×97	35.7
圆锥滚子轴承	Tapered roller bearings	32240	7540E	200×360×104	42.5
圆锥滚子轴承	Tapered roller bearings	32244	7544E	220×400×115	48.1
圆锥滚子轴承	Tapered roller bearings	32248	7548	240×440×127	79.7
圆锥滚子轴承	Tapered roller bearings	32248	7548E	240×440×127	79.7
圆锥滚子轴承	Tapered roller bearings	32252	7552	260×480×137	106
圆锥滚子轴承	Tapered roller bearings	32252	7552E	260×480×137	100.2
圆锥滚子轴承	Tapered roller bearings	32256	7556E	280×500×137	103
圆锥滚子轴承	Tapered roller bearings	33205	3007205	25×52×22	0.221
圆锥滚子轴承	Tapered roller bearings	332/28	30072/28	28×58×24	0.286
圆锥滚子轴承	Tapered roller bearings	33206	3007206	30×62×25	347
圆锥滚子轴承	Tapered roller bearings	33206	3007206E	30×62×25	-
圆锥滚子轴承	Tapered roller bearings	332/32	30072/32	32×65×18.25	-
圆锥滚子轴承	Tapered roller bearings	33207	3007207	35×72×28	0.524
圆锥滚子轴承	Tapered roller bearings	33207	3007207E	35×72×28	-
圆锥滚子轴承	Tapered roller bearings	33208	3007208	40×80×32	0.715
圆锥滚子轴承	Tapered roller bearings	33208	3007208E	40×80×32	-
圆锥滚子轴承	Tapered roller bearings	33209	3007209	45×85×32	0.77
圆锥滚子轴承	Tapered roller bearings	33209	3007209E	45×85×32	-
圆锥滚子轴承	Tapered roller bearings	33210	3007210	50×90×32	0.867
圆锥滚子轴承	Tapered roller bearings	33211	3007211	55×100×35	1.18
圆锥滚子轴承	Tapered roller bearings	33212	3007212	60×110×38	1.56
圆锥滚子轴承	Tapered roller bearings	33213	3007213	65×120×41	2.04
圆锥滚子轴承	Tapered roller bearings	33213	3007213E	65×120×41	1.99
圆锥滚子轴承	Tapered roller bearings	33213/YB2	-	65×120×41	2.02
圆锥滚子轴承	Tapered roller bearings	33214	3007214	70×125×41	2.15
圆锥滚子轴承	Tapered roller bearings	33214	3007214E	70×125×41	2.15
圆锥滚子轴承	Tapered roller bearings	33215	3007215	75×130×41	2.27
圆锥滚子轴承	Tapered roller bearings	33215	3007215E	75×130×41	2.2
圆锥滚子轴承	Tapered roller bearings	33216	3007216	80×140×46	2.89
圆锥滚子轴承	Tapered roller bearings	33217	3007217	85×150×49	3.64
圆锥滚子轴承	Tapered roller bearings	33217	3007217E	85×150×49	3.56
圆锥滚子轴承	Tapered roller bearings	33218	3007218	90×160×55	4.69
圆锥滚子轴承	Tapered roller bearings	33219	3007219	95×170×58	5.54
圆锥滚子轴承	Tapered roller bearings	33220	3007220	100×180×63	6.71
圆锥滚子轴承	Tapered roller bearings	33220	3007220EK	100×180×63	6.71
圆锥滚子轴承	Tapered roller bearings	33221	3007221	105×190×68	-
圆锥滚子轴承	Tapered roller bearings	30302	7302E	15×47×15.25	0.096
圆锥滚子轴承	Tapered roller bearings	-	-	17×47×15.25	-
圆锥滚子轴承	Tapered roller bearings	30303	7303E	-	0.13
圆锥滚子轴承	Tapered roller bearings	30304	7304E	20×52×16.25	0.168
圆锥滚子轴承	Tapered roller bearings	30305	7305E	25×62×18.25	0.259
圆锥滚子轴承	Tapered roller bearings	30306	7306E	30×72×20.75	0.39
圆锥滚子轴承	Tapered roller bearings	30307	7307E	35×80×22.75	0.522
圆锥滚子轴承	Tapered roller bearings	30308	7308E	40×90×25.25	0.747
圆锥滚子轴承	Tapered roller bearings	30309	7309E	45×100×27.25	0.984
圆锥滚子轴承	Tapered roller bearings	30309	7309K	45×100×27.25	1.01
圆锥滚子轴承	Tapered roller bearings	30310	7310K	50×110×29.25	1.25
圆锥滚子轴承	Tapered roller bearings	30311	7311	55×120×31.5	1.585
圆锥滚子轴承	Tapered roller bearings	30311	7311E	55×120×31.5	1.63
圆锥滚子轴承	Tapered roller bearings	30312	7312	60×130×3.5	1.96
圆锥滚子轴承	Tapered roller bearings	30312	7312E	60×130×31.5	1.9
圆锥滚子轴承	Tapered roller bearings	30312	7312K	60×130×31.5	2
圆锥滚子轴承	Tapered roller bearings	30313	7313E	65×140×36	2.41
圆锥滚子轴承	Tapered roller bearings	30314	7314E	70×150×38	3.04
圆锥滚子轴承	Tapered roller bearings	30315	7315E	75×160×40	3.743
圆锥滚子轴承	Tapered roller bearings	30316	7316E	80×170×42.5	4.268
圆锥滚子轴承	Tapered roller bearings	30317	7317E	85×180×44.5	5.39
圆锥滚子轴承	Tapered roller bearings	30318	7318E	90×190×46.5	5.73
圆锥滚子轴承	Tapered roller bearings	30319	7319E	95×200×49.5	6.796
圆锥滚子轴承	Tapered roller bearings	30320	7320E	100×215×51.5	8.09
圆锥滚子轴承	Tapered roller bearings	30321	7321E	105×225×53.5	9.38
圆锥滚子轴承	Tapered roller bearings	30322	7322E	110×240×54.5	-
圆锥滚子轴承	Tapered roller bearings	30324	7324E	120×260×59.5	13.75
圆锥滚子轴承	Tapered roller bearings	30326	7326E	130×280×63.75	17.4
圆锥滚子轴承	Tapered roller bearings	30328	7328E	140×300×63.75	21.2
圆锥滚子轴承	Tapered roller bearings	30330	7330E	150×320×63.75	-
圆锥滚子轴承	Tapered roller bearings	30332	7332E	160×340×75	32.96
圆锥滚子轴承	Tapered roller bearings	30332	7332EK	160×340×75	32.96
圆锥滚子轴承	Tapered roller bearings	30334	7334E	170×360×80	34.16
圆锥滚子轴承	Tapered roller bearings	30336	7336E	180×380×83	45.5
圆锥滚子轴承	Tapered roller bearings	30338	7338E	190×400×86	46.9
圆锥滚子轴承	Tapered roller bearings	30340	7340E	200×420×89	53.4
圆锥滚子轴承	Tapered roller bearings	30344	7344E	220×460×97	69.6
圆锥滚子轴承	Tapered roller bearings	30348	7348E	240×500×105	88.9
圆锥滚子轴承	Tapered roller bearings	30352	7352	260×540×113	111.3
圆锥滚子轴承	Tapered roller bearings	30352	7352E	260×540×113	111.3
圆锥滚子轴承	Tapered roller bearings	32303	7603E	17×47×20.25	0.174
圆锥滚子轴承	Tapered roller bearings	32304	7604E	20×52×22.25	0.238
圆锥滚子轴承	Tapered roller bearings	32305	7605E	25×62×25.25	0.36
圆锥滚子轴承	Tapered roller bearings	32305	7605EK	25×62×25.5	0.366
圆锥滚子轴承	Tapered roller bearings	32306	7606E	30×72×28.75	0.544
圆锥滚子轴承	Tapered roller bearings	32306	7606K	30×72×28.75	0.574
圆锥滚子轴承	Tapered roller bearings	32306AN	-	30×72×28.75	0.698
圆锥滚子轴承	Tapered roller bearings	323/32	76/32	32×75×29.75	0.647
圆锥滚子轴承	Tapered roller bearings	323/32CN	-	32×75×29.75	-
圆锥滚子轴承	Tapered roller bearings	32307	7607E	35×80×32.75	0.804
圆锥滚子轴承	Tapered roller bearings	32307	7607EK	35×80×32.75	0.804
圆锥滚子轴承	Tapered roller bearings	32308	7608E	40×90×35.25	1.045
圆锥滚子轴承	Tapered roller bearings	32308/YB2	7608EK	40×90×35.25	1.02
圆锥滚子轴承	Tapered roller bearings	32308	7608K	40×90×35.25	1.01
圆锥滚子轴承	Tapered roller bearings	32308	7608EK	40×90×35.25	1.01
圆锥滚子轴承	Tapered roller bearings	32309	7609E	45×100×38.2	1.36
圆锥滚子轴承	Tapered roller bearings	32310	7610E	50×110×42.25	1.74
圆锥滚子轴承	Tapered roller bearings	32310/YA	7610EK	50×110×42.25	1.88
圆锥滚子轴承	Tapered roller bearings	32310	7610K	50×110×42.25	1.78
圆锥滚子轴承	Tapered roller bearings	32311	7611E	55×120×45.5	2.2
圆锥滚子轴承	Tapered roller bearings	32311	7611K	55×120×46	2.39
圆锥滚子轴承	Tapered roller bearings	32311/YA	7611EK	55×120×45.5	2.43
圆锥滚子轴承	Tapered roller bearings	32311/YB2	7611EK	55×120×45.5	2.35
圆锥滚子轴承	Tapered roller bearings	32312	7612E	60×130×48.5	2.99
圆锥滚子轴承	Tapered roller bearings	32312	7612EK	60×130×48.5	2.79
圆锥滚子轴承	Tapered roller bearings	32313	7613E	65×140×51	3.45
圆锥滚子轴承	Tapered roller bearings	32313	7613EK	65×140×51	3.63
圆锥滚子轴承	Tapered roller bearings	32314	7614E	70×150×54	4.26
圆锥滚子轴承	Tapered roller bearings	32315	7615E	75×160×58	5.29
圆锥滚子轴承	Tapered roller bearings	32316	7616E	80×170×67.5	5.96
圆锥滚子轴承	Tapered roller bearings	32317	7617E	85×180×63.5	-
圆锥滚子轴承	Tapered roller bearings	32318	7618E	90×190×67.5	8.784
圆锥滚子轴承	Tapered roller bearings	32319	7619E	95×200×71.5	10
圆锥滚子轴承	Tapered roller bearings	32320	7620E	100×215×77.5	13.2
圆锥滚子轴承	Tapered roller bearings	32321	7621E	105×225×81.5	14.4
圆锥滚子轴承	Tapered roller bearings	32322	7622E	110×240×84.5	18
圆锥滚子轴承	Tapered roller bearings	32324	7624E	120×260×90.5	22.4
圆锥滚子轴承	Tapered roller bearings	32326	7626E	130×280×98.75	26.6
圆锥滚子轴承	Tapered roller bearings	32328	7628E	140×300×107.75	-
圆锥滚子轴承	Tapered roller bearings	32330	7630E	150×320×114	37.1
圆锥滚子轴承	Tapered roller bearings	32332	7632E	160×340×121	51.7
圆锥滚子轴承	Tapered roller bearings	32334	7634E	170×360×127	58.3
圆锥滚子轴承	Tapered roller bearings	32336	7636E	180×380×134	64.8
圆锥滚子轴承	Tapered roller bearings	32338	7638E	190×400×140	74.8
圆锥滚子轴承	Tapered roller bearings	32340	7640E	200×420×146	86
圆锥滚子轴承	Tapered roller bearings	32344	7644E	220×460×154	108
圆锥滚子轴承	Tapered roller bearings	32348	7648E	240×500×165	137
圆锥滚子轴承	Tapered roller bearings	32352	7652E	260×540×176	187
圆锥滚子轴承	Tapered roller bearings	32356	7656E	280×580×187	208
圆锥滚子轴承	Tapered roller bearings	308/800YB2	-	800×990×57	96.3
圆锥滚子轴承	Tapered roller bearings	31856X2	1007856	280×350×36	6.33
圆锥滚子轴承	Tapered roller bearings	318/850X2	10078/850	850×1030×90	142
圆锥滚子轴承	Tapered roller bearings	32880X2	7880	400×500×60	25.1
圆锥滚子轴承	Tapered roller bearings	32880X2	7880E	400×500×60	25.1
圆锥滚子轴承	Tapered roller bearings	31976X2	1007976	380×520×66.5	37.5
圆锥滚子轴承	Tapered roller bearings	31984X2	1007984	420×560×70	42.5
圆锥滚子轴承	Tapered roller bearings	31992X2	1007992	460×620×80	60
圆锥滚子轴承	Tapered roller bearings	31996X2	1007996	480×650×84.2	71
圆锥滚子轴承	Tapered roller bearings	319/530X2	10079/530	530×170×88	94.7
圆锥滚子轴承	Tapered roller bearings	319/560X2	10079/560	560×750×92.5	105
圆锥滚子轴承	Tapered roller bearings	319/710X2	10079/710	710×950×114	210.2
圆锥滚子轴承	Tapered roller bearings	319/800X2	10079/800	800×1060×122	275
圆锥滚子轴承	Tapered roller bearings	319/900X2	10079/900	900×1180×124	330
圆锥滚子轴承	Tapered roller bearings	319/950X2	10079/950	950×1250×140	428.2
圆锥滚子轴承	Tapered roller bearings	32922X2	2007922	110×150×25.4	1.18
圆锥滚子轴承	Tapered roller bearings	32926X2	2007926	130×180×32.5	2.31
圆锥滚子轴承	Tapered roller bearings	32928X2	2007928	140×190×32.5	-
圆锥滚子轴承	Tapered roller bearings	32930X2	2007930	150×210×38.5	-
圆锥滚子轴承	Tapered roller bearings	32932X2	2007932	160×220×38.5	-
圆锥滚子轴承	Tapered roller bearings	32934X2	2007934	170×230×38.5	-
圆锥滚子轴承	Tapered roller bearings	32934YA	2007934	170×230×38.5	-
圆锥滚子轴承	Tapered roller bearings	32938X2	2007938	190×260×45.5	-
圆锥滚子轴承	Tapered roller bearings	32940X2	2007940	200×280×51.5	-
圆锥滚子轴承	Tapered roller bearings	32940X2/YA	2007940K	200×280×52	8.7
圆锥滚子轴承	Tapered roller bearings	32944X2	2007944	220×300×51.5	-
圆锥滚子轴承	Tapered roller bearings	32948X2	2007948	240×320×51.5	-
圆锥滚子轴承	Tapered roller bearings	32952X2	2007952	260×360×64.5	19.2
圆锥滚子轴承	Tapered roller bearings	32952X2/YB2	2007952K	260×360×64.5	18.7
圆锥滚子轴承	Tapered roller bearings	32956X2	2007956	280×380×64.5	21.3
圆锥滚子轴承	Tapered roller bearings	32956X2/YB2	2007956K	280×380×64.5	19.8
圆锥滚子轴承	Tapered roller bearings	32960X2	2007960	300×420×76.5	-
圆锥滚子轴承	Tapered roller bearings	32964X2	2007964	320×440×76.5	44.7
圆锥滚子轴承	Tapered roller bearings	32968X2	2007968	340×460×76.5	34.3
圆锥滚子轴承	Tapered roller bearings	32972X2	2007972	360×480×76.5	35.9
圆锥滚子轴承	Tapered roller bearings	329/500X2	20079/500	500×640×87	66.24
圆锥滚子轴承	Tapered roller bearings	31038X2	7138	190×290×51	13.5
圆锥滚子轴承	Tapered roller bearings	31068X2	7168	340×520×86	57
圆锥滚子轴承	Tapered roller bearings	31072X2	7172	360×540×86	64.75
圆锥滚子轴承	Tapered roller bearings	31080X2	7180	400×600×95	84
圆锥滚子轴承	Tapered roller bearings	31084X2	7184	420×620×95	91.7
圆锥滚子轴承	Tapered roller bearings	31088X2	7188	440×650×96.4	99.4
圆锥滚子轴承	Tapered roller bearings	31092X2	7192	460×680×105	118
圆锥滚子轴承	Tapered roller bearings	310/500X2	71/500	500×720×110	135
圆锥滚子轴承	Tapered roller bearings	310/560X2	71/560	560×820×121	191
圆锥滚子轴承	Tapered roller bearings	310/600X2	71/600	600×870×124	235
圆锥滚子轴承	Tapered roller bearings	310/630X2	71/630	630×920×135	278
圆锥滚子轴承	Tapered roller bearings	310/900X2	71/900	900×1280×190	703
圆锥滚子轴承	Tapered roller bearings	32006X2	2007106	30×55×17.2	0.164
圆锥滚子轴承	Tapered roller bearings	32007X1	7707E	35×65×18	0.229
圆锥滚子轴承	Tapered roller bearings	32007X1/YB	7707EY	35×65×18	0.229
圆锥滚子轴承	Tapered roller bearings	32008X1/WC	-	40×72×19	0.315
圆锥滚子轴承	Tapered roller bearings	32009X2	2007109	45×75×20.2	0.317
圆锥滚子轴承	Tapered roller bearings	32010X2	2007110	50×80×20.2	0.35
圆锥滚子轴承	Tapered roller bearings	32012X2/HVS0	2007112XT	60×95×23.3	0.944
圆锥滚子轴承	Tapered roller bearings	32013X2	2007113	65×100×63.3	0.629
圆锥滚子轴承	Tapered roller bearings	32015X2/HV	2007115X	75×115×25.3	0.867
圆锥滚子轴承	Tapered roller bearings	32016X2/HV	2007116X	80×125×29	1.25
圆锥滚子轴承	Tapered roller bearings	32018X2	2007118	90×140×32.4	1.71
圆锥滚子轴承	Tapered roller bearings	32019X2	2007119	95×145×32.4	1.7
圆锥滚子轴承	Tapered roller bearings	32020X2	2007120	100×150×34.5	1.785
圆锥滚子轴承	Tapered roller bearings	32021X2	2007121E	105×160×35.4	2.5
圆锥滚子轴承	Tapered roller bearings	32022X2/S0	2007122	110×170×38.4	3.12
圆锥滚子轴承	Tapered roller bearings	32022X2	2007122T	110×170×38.4	3.12
圆锥滚子轴承	Tapered roller bearings	32024X2	2007124	120×180×38.4	3.66
圆锥滚子轴承	Tapered roller bearings	32026X2	2007126	130×200×45.5	4.66
圆锥滚子轴承	Tapered roller bearings	32028X2/L2	2007128	140×210×45.5	4.94
圆锥滚子轴承	Tapered roller bearings	32028X2	2007128EL	140×210×45.5	5.1
圆锥滚子轴承	Tapered roller bearings	32030X2	2007130	150×225×48.5	6.75
圆锥滚子轴承	Tapered roller bearings	32032X2	2007132	160×240×51.5	7.67
圆锥滚子轴承	Tapered roller bearings	32032X2/YA	2007132K	160×240×51.5	7.7
圆锥滚子轴承	Tapered roller bearings	32034X2	2007134	170×260×57.5	10.1
圆锥滚子轴承	Tapered roller bearings	32036X2	2007136	180×280×64.5	13
圆锥滚子轴承	Tapered roller bearings	32036X2	7736	180×290×65	15.6
圆锥滚子轴承	Tapered roller bearings	32038X2	2007138	190×290×64.5	15.3
圆锥滚子轴承	Tapered roller bearings	32038X2/HV	2007138N	190×290×64.5	14.1
圆锥滚子轴承	Tapered roller bearings	32038X2	2007138	190×290×64.5	14.1
圆锥滚子轴承	Tapered roller bearings	32040X2	2007140	200×310×70.5	16.2
圆锥滚子轴承	Tapered roller bearings	32044X2	2007144	220×340×76.5	23.2
圆锥滚子轴承	Tapered roller bearings	32044X2/C2	2G2007144	220×340×76.5	22.2
圆锥滚子轴承	Tapered roller bearings	32044X2	7244	220×400×73	37.6
圆锥滚子轴承	Tapered roller bearings	32044X2/S0	7244T	220×400×73	35.4
圆锥滚子轴承	Tapered roller bearings	32048X2	2007148	240×360×76.5	23.8
圆锥滚子轴承	Tapered roller bearings	32052X2	2007152	260×400×87.7	37.8
圆锥滚子轴承	Tapered roller bearings	32056X2	2007156	280×420×87.7	39.6
圆锥滚子轴承	Tapered roller bearings	32060X2	2007160	300×460×100.7	57
圆锥滚子轴承	Tapered roller bearings	32060X2/C4	4G2007160	300×460×100.7	55.9
圆锥滚子轴承	Tapered roller bearings	32064X2	2007164	320×480×100.7	59
圆锥滚子轴承	Tapered roller bearings	32088X2	2007188	440×650×96.4	99
圆锥滚子轴承	Tapered roller bearings	32088X2/YA	2007188K	440×650×96.4	98.2
圆锥滚子轴承	Tapered roller bearings	31160X2	1007760	300×500×95	67.7
圆锥滚子轴承	Tapered roller bearings	32007X2	2007117E	85×130×29	1.32
圆锥滚子轴承	Tapered roller bearings	33011X2	-	55×90×52	1.23
圆锥滚子轴承	Tapered roller bearings	33113X2	7813	65×110×30.3	1.1
圆锥滚子轴承	Tapered roller bearings	33113X2	7813E	65×110×30.3	1.1
圆锥滚子轴承	Tapered roller bearings	33113X2	7813EY	65×110×30.5	-
圆锥滚子轴承	Tapered roller bearings	33113X2/YB	7813Y	65×110×30.3	1.1
圆锥滚子轴承	Tapered roller bearings	33113X2	7813	65×110×30.5	-
圆锥滚子轴承	Tapered roller bearings	33113X2	7813E	65×110×30.5	1.13
圆锥滚子轴承	Tapered roller bearings	33113X2/YA	7813K	65×110×30.5	1.1
圆锥滚子轴承	Tapered roller bearings	331133X2	7813EK	65×110×30.5	-
圆锥滚子轴承	Tapered roller bearings	331133X2	7813E	65×110×31	-
圆锥滚子轴承	Tapered roller bearings	33114X2	7814E	70×120×33	1.46
圆锥滚子轴承	Tapered roller bearings	33114X2	7814	70×117×37	1.33
圆锥滚子轴承	Tapered roller bearings	33116X2	7716E	80×130×32	1.6
圆锥滚子轴承	Tapered roller bearings	33118X2	3007718	90×150×48	3.22
圆锥滚子轴承	Tapered roller bearings	33118X2	-	90×160×38.5	2.57
圆锥滚子轴承	Tapered roller bearings	33118X2	3007718	90×160×45	3.22
圆锥滚子轴承	Tapered roller bearings	30203X2	7203	17×40×13.5	0.074
圆锥滚子轴承	Tapered roller bearings	30204X2	7204	20×47×15.5	0.118
圆锥滚子轴承	Tapered roller bearings	30205X2	7205	25×52×16.5	0.15
圆锥滚子轴承	Tapered roller bearings	30208X2	7808E	40×90×21.5	0.446
圆锥滚子轴承	Tapered roller bearings	30211X2/YA	-	55×100×21	0.689
圆锥滚子轴承	Tapered roller bearings	30215X2	7215E	75×130×27.3	1.36
圆锥滚子轴承	Tapered roller bearings	30218X2	7218	90×160×33	2.53
圆锥滚子轴承	Tapered roller bearings	30219X2/HV	7219X	95×170×35	3.17
圆锥滚子轴承	Tapered roller bearings	30220X2/HV	7220X	100×180×37	-
圆锥滚子轴承	Tapered roller bearings	30224X2	7224	120×215×44	5.91
圆锥滚子轴承	Tapered roller bearings	30226X2	7226E	130×230×44.5	7.25
圆锥滚子轴承	Tapered roller bearings	30230X2	7230E	150×270×48.5	11.2
圆锥滚子轴承	Tapered roller bearings	30244	7244	220×400×73	35.4
圆锥滚子轴承	Tapered roller bearings	32210X2	7510	50×90×25	0.612
圆锥滚子轴承	Tapered roller bearings	32213X2	7513	65×110×33	1.5
圆锥滚子轴承	Tapered roller bearings	32215X2	7515	75×130×34	1.68
圆锥滚子轴承	Tapered roller bearings	32216X2	7516	80×140×36	2.13
圆锥滚子轴承	Tapered roller bearings	32216X2/HV	7516X	80×140×36	2.13
圆锥滚子轴承	Tapered roller bearings	32216X2/Z	7516Z	80×140×36	2.13
圆锥滚子轴承	Tapered roller bearings	32218X2	7518	90×160×43	3.36
圆锥滚子轴承	Tapered roller bearings	32220X2	7520	100×180×49.5	4.94
圆锥滚子轴承	Tapered roller bearings	32222X2	7522K	110×200×56.5	7.7
圆锥滚子轴承	Tapered roller bearings	32226X2	7526	130×230×68.5	11.1
圆锥滚子轴承	Tapered roller bearings	32244X2	7544	220×400×115	48.1
圆锥滚子轴承	Tapered roller bearings	32244X2	7544E	220×400×115	48.1
圆锥滚子轴承	Tapered roller bearings	33209X3	7809E	40×90×38.5	1.11
圆锥滚子轴承	Tapered roller bearings	33215X2	7217	75×130×44.5	2.57
圆锥滚子轴承	Tapered roller bearings	33216X2	7816E	80×140×45	2.77
圆锥滚子轴承	Tapered roller bearings	33217/HV	7217X	85×150×31	2.03
圆锥滚子轴承	Tapered roller bearings	33218X2	7718	90×160×50	3.867
圆锥滚子轴承	Tapered roller bearings	33218X2	7718E	90×160×50	3.83
圆锥滚子轴承	Tapered roller bearings	30322	7322E	110×240×63	11.1
圆锥滚子轴承	Tapered roller bearings	30328X2	7828	140×300×90	29
圆锥滚子轴承	Tapered roller bearings	30328X2	7828E	140×300×90	29
圆锥滚子轴承	Tapered roller bearings	30352X2	7352	260×540×114	113
圆锥滚子轴承	Tapered roller bearings	32310X2	7610E	50×110×29	-
圆锥滚子轴承	Tapered roller bearings	323/32X1TN1	7806EA	32×72×29.75	-
圆锥滚子轴承	Tapered roller bearings	32320X2	7620	100×215×78	12.7
圆锥滚子轴承	Tapered roller bearings	32321X3	7721E	100×215×78	12.6
圆锥滚子轴承	Tapered roller bearings	32326X2	7626	130×280×99.5	26.4
圆锥滚子轴承	Tapered roller bearings	32326X2	7626E	130×280×99.5	26.4
圆锥滚子轴承	Tapered roller bearings	32334X2	7634	170×360×128	63.5
圆锥滚子轴承	Tapered roller bearings	33113X2	7813E	65×110×30.5	1.1
圆锥滚子轴承	Tapered roller bearings	33113X2	7813EK	65×110×30.5	-
圆锥滚子轴承	Tapered roller bearings	33113X2	7813EY	65×110×30.5	-
圆锥滚子轴承	Tapered roller bearings	T2ED045	-	45×95×36	1.18
圆锥滚子轴承	Tapered roller bearings	T2ED070	7714E